(file) Return to sw_functions.c CVS log (file) (dir) Up to [Development] / JSOC / proj / sharp / apps

Diff for /JSOC/proj/sharp/apps/sw_functions.c between version 1.21 and 1.30

version 1.21, 2013/11/11 23:18:40 version 1.30, 2014/06/02 19:46:44
Line 17 
Line 17 
     MEANPOT Mean photospheric excess magnetic energy density in ergs per cubic centimeter     MEANPOT Mean photospheric excess magnetic energy density in ergs per cubic centimeter
     TOTPOT Total photospheric magnetic energy density in ergs per cubic centimeter     TOTPOT Total photospheric magnetic energy density in ergs per cubic centimeter
     MEANSHR Mean shear angle (measured using Btotal) in degrees     MEANSHR Mean shear angle (measured using Btotal) in degrees
    R_VALUE Karel Schrijver's R parameter
  
    The indices are calculated on the pixels in which the conf_disambig segment is greater than 70 and    The indices are calculated on the pixels in which the conf_disambig segment is greater than 70 and
    pixels in which the bitmap segment is greater than 30. These ranges are selected because the CCD    pixels in which the bitmap segment is greater than 30. These ranges are selected because the CCD
Line 1027  int computeShearAngle(float *bx_err, flo
Line 1028  int computeShearAngle(float *bx_err, flo
         /* The area here is a fractional area -- the % of the total area. This has no error associated with it. */         /* The area here is a fractional area -- the % of the total area. This has no error associated with it. */
         *area_w_shear_gt_45ptr   = (count_mask/(count))*(100.0);         *area_w_shear_gt_45ptr   = (count_mask/(count))*(100.0);
  
         printf("MEANSHR=%f\n",*meanshear_angleptr);      //printf("MEANSHR=%f\n",*meanshear_angleptr);
         printf("MEANSHR_err=%f\n",*meanshear_angle_err_ptr);      //printf("MEANSHR_err=%f\n",*meanshear_angle_err_ptr);
         printf("SHRGT45=%f\n",*area_w_shear_gt_45ptr);      //printf("SHRGT45=%f\n",*area_w_shear_gt_45ptr);
  
         return 0;         return 0;
 } }
  
   /*===========================================*/
   /* Example function 15: R parameter as defined in Schrijver, 2007 */
   //
   // Note that there is a restriction on the function fsample()
   // If the following occurs:
   //      nx_out > floor((ny_in-1)/scale + 1)
   //      ny_out > floor((ny_in-1)/scale + 1),
   // where n*_out are the dimensions of the output array and n*_in
   // are the dimensions of the input array, fsample() will usually result
   // in a segfault (though not always, depending on how the segfault was accessed.)
   
   int computeR(float *bz_err, float *los, int *dims, float *Rparam, float cdelt1,
                float *rim, float *p1p0, float *p1n0, float *p1p, float *p1n, float *p1,
                float *pmap, int nx1, int ny1,
                int scale, float *p1pad, int nxp, int nyp, float *pmapn)
   
   {
       int nx = dims[0];
       int ny = dims[1];
       int i = 0;
       int j = 0;
       int index, index1;
       double sum = 0.0;
       double err = 0.0;
       *Rparam = 0.0;
       struct fresize_struct fresboxcar, fresgauss;
       struct fint_struct fints;
       float sigma = 10.0/2.3548;
   
       // set up convolution kernels
       init_fresize_boxcar(&fresboxcar,1,1);
       init_fresize_gaussian(&fresgauss,sigma,20,1);
   
       // =============== [STEP 1] ===============
       // bin the line-of-sight magnetogram down by a factor of scale
       fsample(los, rim, nx, ny, nx, nx1, ny1, nx1, scale, 0, 0, 0.0);
   
       // =============== [STEP 2] ===============
       // identify positive and negative pixels greater than +/- 150 gauss
       // and label those pixels with a 1.0 in arrays p1p0 and p1n0
       for (i = 0; i < nx1; i++)
       {
           for (j = 0; j < ny1; j++)
           {
               index = j * nx1 + i;
               if (rim[index] > 150)
                   p1p0[index]=1.0;
               else
                   p1p0[index]=0.0;
               if (rim[index] < -150)
                   p1n0[index]=1.0;
               else
                   p1n0[index]=0.0;
           }
       }
   
       // =============== [STEP 3] ===============
       // smooth each of the negative and positive pixel bitmaps
       fresize(&fresboxcar, p1p0, p1p, nx1, ny1, nx1, nx1, ny1, nx1, 0, 0, 0.0);
       fresize(&fresboxcar, p1n0, p1n, nx1, ny1, nx1, nx1, ny1, nx1, 0, 0, 0.0);
   
       // =============== [STEP 4] ===============
       // find the pixels for which p1p and p1n are both equal to 1.
       // this defines the polarity inversion line
       for (i = 0; i < nx1; i++)
       {
           for (j = 0; j < ny1; j++)
           {
               index = j * nx1 + i;
               if ((p1p[index] > 0.0) && (p1n[index] > 0.0))
                   p1[index]=1.0;
               else
                   p1[index]=0.0;
           }
       }
   
       // pad p1 with zeroes so that the gaussian colvolution in step 5
       // does not cut off data within hwidth of the edge
   
       // step i: zero p1pad
       for (i = 0; i < nxp; i++)
       {
           for (j = 0; j < nyp; j++)
           {
               index = j * nxp + i;
               p1pad[index]=0.0;
           }
       }
   
       // step ii: place p1 at the center of p1pad
       for (i = 0; i < nx1; i++)
       {
          for (j = 0; j < ny1; j++)
          {
               index  = j * nx1 + i;
               index1 = (j+20) * nxp + (i+20);
               p1pad[index1]=p1[index];
           }
       }
   
       // =============== [STEP 5] ===============
       // convolve the polarity inversion line map with a gaussian
       // to identify the region near the plarity inversion line
       // the resultant array is called pmap
       fresize(&fresgauss, p1pad, pmap, nxp, nyp, nxp, nxp, nyp, nxp, 0, 0, 0.0);
   
   
      // select out the nx1 x ny1 non-padded array  within pmap
       for (i = 0; i < nx1; i++)
       {
          for (j = 0; j < ny1; j++)
          {
               index  = j * nx1 + i;
               index1 = (j+20) * nxp + (i+20);
               pmapn[index]=pmap[index1];
           }
       }
   
       // =============== [STEP 6] ===============
       // the R parameter is calculated
       for (i = 0; i < nx1; i++)
       {
           for (j = 0; j < ny1; j++)
           {
               index = j * nx1 + i;
               sum += pmapn[index]*abs(rim[index]);
           }
       }
   
       if (sum < 1.0)
           *Rparam = 0.0;
       else
           *Rparam = log10(sum);
   
       free_fresize(&fresboxcar);
       free_fresize(&fresgauss);
   
       return 0;
   
   }
  
 /*==================KEIJI'S CODE =========================*/ /*==================KEIJI'S CODE =========================*/
  
Line 1153  void greenpot(float *bx, float *by, floa
Line 1294  void greenpot(float *bx, float *by, floa
  
 char *sw_functions_version() // Returns CVS version of sw_functions.c char *sw_functions_version() // Returns CVS version of sw_functions.c
 { {
   return strdup("$Id$");      return strdup("$Id");
 } }
  
 /* ---------------- end of this file ----------------*/ /* ---------------- end of this file ----------------*/


Legend:
Removed from v.1.21  
changed lines
  Added in v.1.30

Karen Tian
Powered by
ViewCVS 0.9.4